Skip to content

ESP32-S3-DevKitC-1 (N8R8)

Report component

Tell our team what needs attention. You must be signed in to send a report.

Up to 2,000 characters. Include what the team should check.

A newer, faster ESP32 with extra memory, good for projects that listen, see or think on the device.

ESP32-S3 dual-core 240 MHz with Wi-Fi, Bluetooth LE, 8 MB flash and 8 MB PSRAM. Vector instructions for on-device ML. 3.3 V logic, native USB.

Electrical

Supply voltage
4.75 to 5.25 V
Logic level
3.3 V
Current
90 mA typical, 500 mA max
Talks over
digital, analog, pwm, i2c, spi, uart
Board
esp32, 3.3 V logic, 1100 mA total GPIO

Pins

PinCan doMax VMax mA
GPIO1digital, PWM, analog, interruptADC1: works with Wi-Fi on.3.620
GPIO2digital, PWM, analog, interruptADC1: works with Wi-Fi on.3.620
GPIO4digital, PWM, analog, interruptADC1: works with Wi-Fi on.3.620
GPIO5digital, PWM, analog, interruptADC1: works with Wi-Fi on.3.620
GPIO6digital, PWM, analog, interruptADC1: works with Wi-Fi on.3.620
GPIO7digital, PWM, analog, interruptADC1: works with Wi-Fi on.3.620
GPIO3digital, PWM, analog, interrupt, boot pinStrapping pin (JTAG select). ADC1.3.620
GPIO8digital, PWM, analog, interrupt, I2C dataDefault I2C SDA (Arduino core). ADC1.3.620
GPIO9digital, PWM, analog, interrupt, I2C clockDefault I2C SCL (Arduino core). ADC1.3.620
GPIO10digital, PWM, analog, interrupt, SPI selectDefault SPI CS. ADC1.3.620
GPIO11digital, PWM, analog, interrupt, SPI MOSIDefault SPI MOSI. ADC2: not readable while Wi-Fi is on.3.620
GPIO12digital, PWM, analog, interrupt, SPI clockDefault SPI SCK. ADC2: not readable while Wi-Fi is on.3.620
GPIO13digital, PWM, analog, interrupt, SPI MISODefault SPI MISO. ADC2: not readable while Wi-Fi is on.3.620
GPIO14digital, PWM, analog, interruptADC2: not readable while Wi-Fi is on.3.620
GPIO15digital, PWM, analog, interruptADC2: not readable while Wi-Fi is on.3.620
GPIO16digital, PWM, analog, interruptADC2: not readable while Wi-Fi is on.3.620
GPIO17digital, PWM, analog, interruptADC2: not readable while Wi-Fi is on.3.620
GPIO18digital, PWM, analog, interruptADC2: not readable while Wi-Fi is on.3.620
GPIO19digital, PWM, analog, interruptNative USB D-. Avoid if you use the USB port. ADC2: not readable while Wi-Fi is on.3.620
GPIO20digital, PWM, analog, interruptNative USB D+. Avoid if you use the USB port. ADC2: not readable while Wi-Fi is on.3.620
GPIO21digital, PWM, interrupt3.620
GPIO35reservedUsed by the octal PSRAM on N8R8 modules. Never use.3.620
GPIO36reservedUsed by the octal PSRAM on N8R8 modules. Never use.3.620
GPIO37reservedUsed by the octal PSRAM on N8R8 modules. Never use.3.620
GPIO38digital, PWM, interruptDrives the RGB LED on v1.1 boards.3.620
GPIO39digital, PWM, interrupt3.620
GPIO40digital, PWM, interrupt3.620
GPIO41digital, PWM, interrupt3.620
GPIO42digital, PWM, interrupt3.620
GPIO47digital, PWM, interrupt3.620
GPIO48digital, PWM, interruptDrives the RGB LED on v1.0 boards.3.620
GPIO43digital, serial TXUART0 TX (USB-UART port). Leave free for logs.3.620
GPIO44digital, serial RXUART0 RX (USB-UART port). Leave free for logs.3.620
GPIO0digital, PWM, interrupt, boot pinBOOT button. Must be HIGH at boot.3.620
GPIO45digital, PWM, interrupt, boot pinSets flash voltage at boot: keep LOW.3.620
GPIO46digital, interrupt, boot pinMust be LOW at boot for USB download mode.3.620
3V33.3 VRegulated 3.3 V out, shared with the module.500
3V3_23.3 V500
5V5 V, power in5 V from USB, or feed a regulated 5 V in here.
RSTnot connectedChip enable / reset.
GNDground
GND2ground
GND3ground
GND4ground

Size and material

Size
25 × 10 × 69 mm
Material
pcb
Sold by the
piece

Projects using it

No public project uses it yet. Design one that does.