ESP32 DevKitC (ESP32-WROOM-32, 38-pin)
A small computer with Wi-Fi and Bluetooth built in, so your project can talk to your phone or the internet.
Espressif's dual-core 240 MHz Wi-Fi + Bluetooth board. 3.3 V logic (not 5 V tolerant), 12-bit ADC, 2 DACs, PWM on every output pin. Powered from USB.
Electrical
- Supply voltage
- 4.75 to 5.25 V
- Logic level
- 3.3 V
- Current
- 80 mA typical, 500 mA max
- Talks over
- digital, analog, pwm, i2c, spi, uart
- Board
- esp32, 3.3 V logic, 1100 mA total GPIO
Pins
| Pin | Can do | Max V | Max mA |
|---|---|---|---|
| GPIO0 | digital, PWM, analog, interrupt, boot pinBOOT button. Must be HIGH at boot. ADC2: not readable while Wi-Fi is on. | 3.6 | 20 |
| GPIO1 | digital, serial TXUSB serial TX (TX0). Leave free for uploads and logs. | 3.6 | 20 |
| GPIO2 | digital, PWM, analog, interrupt, boot pinMust be LOW or floating at boot. ADC2: not readable while Wi-Fi is on. | 3.6 | 20 |
| GPIO3 | digital, serial RXUSB serial RX (RX0). Leave free for uploads and logs. | 3.6 | 20 |
| GPIO4 | digital, PWM, analog, interruptADC2: not readable while Wi-Fi is on. | 3.6 | 20 |
| GPIO5 | digital, PWM, interrupt, SPI select, boot pinVSPI CS. Outputs a PWM signal at boot. | 3.6 | 20 |
| GPIO6 | reservedWired to the on-module SPI flash. Never use. | 3.6 | 20 |
| GPIO7 | reservedWired to the on-module SPI flash. Never use. | 3.6 | 20 |
| GPIO8 | reservedWired to the on-module SPI flash. Never use. | 3.6 | 20 |
| GPIO9 | reservedWired to the on-module SPI flash. Never use. | 3.6 | 20 |
| GPIO10 | reservedWired to the on-module SPI flash. Never use. | 3.6 | 20 |
| GPIO11 | reservedWired to the on-module SPI flash. Never use. | 3.6 | 20 |
| GPIO12 | digital, PWM, analog, interrupt, boot pinSets flash voltage at boot: keep LOW at boot. ADC2: not readable while Wi-Fi is on. | 3.6 | 20 |
| GPIO13 | digital, PWM, analog, interruptADC2: not readable while Wi-Fi is on. | 3.6 | 20 |
| GPIO14 | digital, PWM, analog, interruptOutputs PWM at boot. ADC2: not readable while Wi-Fi is on. | 3.6 | 20 |
| GPIO15 | digital, PWM, analog, interrupt, boot pinOutputs PWM at boot. ADC2: not readable while Wi-Fi is on. | 3.6 | 20 |
| GPIO16 | digital, PWM, interrupt, serial RXUART2 RX. | 3.6 | 20 |
| GPIO17 | digital, PWM, interrupt, serial TXUART2 TX. | 3.6 | 20 |
| GPIO18 | digital, PWM, interrupt, SPI clockVSPI SCK. | 3.6 | 20 |
| GPIO19 | digital, PWM, interrupt, SPI MISOVSPI MISO. | 3.6 | 20 |
| GPIO21 | digital, PWM, interrupt, I2C dataDefault I2C SDA. | 3.6 | 20 |
| GPIO22 | digital, PWM, interrupt, I2C clockDefault I2C SCL. | 3.6 | 20 |
| GPIO23 | digital, PWM, interrupt, SPI MOSIVSPI MOSI. | 3.6 | 20 |
| GPIO25 | digital, PWM, analog, DAC, interruptDAC1. ADC2: not readable while Wi-Fi is on. | 3.6 | 20 |
| GPIO26 | digital, PWM, analog, DAC, interruptDAC2. ADC2: not readable while Wi-Fi is on. | 3.6 | 20 |
| GPIO27 | digital, PWM, analog, interruptADC2: not readable while Wi-Fi is on. | 3.6 | 20 |
| GPIO32 | digital, PWM, analog, interruptADC1: works with Wi-Fi on. | 3.6 | 20 |
| GPIO33 | digital, PWM, analog, interruptADC1: works with Wi-Fi on. | 3.6 | 20 |
| GPIO34 | digital, analog, input only, interruptInput only, no internal pull-up. ADC1: works with Wi-Fi on. | 3.6 | 20 |
| GPIO35 | digital, analog, input only, interruptInput only, no internal pull-up. ADC1: works with Wi-Fi on. | 3.6 | 20 |
| GPIO36 | digital, analog, input only, interruptInput only, no internal pull-up. ADC1: works with Wi-Fi on. | 3.6 | 20 |
| GPIO39 | digital, analog, input only, interruptInput only, no internal pull-up. ADC1: works with Wi-Fi on. | 3.6 | 20 |
| 3V3 | 3.3 VRegulated 3.3 V out. Shared with the ESP32 itself (Wi-Fi peaks ~350 mA). | 500 | |
| 5V | 5 V, power in5 V from USB, or feed a regulated 5 V in here. | ||
| EN | not connectedChip enable / reset. Pull LOW to reset. | ||
| GND | ground | ||
| GND2 | ground | ||
| GND3 | ground |
Size and material
- Size
- 28 × 10 × 54 mm
- Material
- pcb
- Sold by the
- piece


