PCA9685 16-channel 12-bit PWM / servo driver (I2C)
Runs up to 16 servos or dimmable lights from just two board pins.
Adafruit PCA9685 breakout: 16 independent PWM outputs (12-bit, up to about 1.6 kHz) driven over two I2C wires, with 220 Ω series resistors and four 3x4 servo headers. Logic 3-5 V; servo power on the V+ terminal. Address 0x40 by default, 0x40-0x7F with jumpers (0x70 is the all-call address). 62.5 x 25.4 x 3 mm.
Electrical
- Supply voltage
- 3 to 5.5 V
- Current
- 10 mA typical, 25 mA max
- Talks over
- i2c
- I2C address
- 0x40, 0x41, 0x42, 0x43, 0x44, 0x45, 0x46, 0x47
Needs alongside it
- Feed servo power (5-6 V, sized for all servos moving) into V+, not from the board.
Pins
| Pin | Can do | Max V | Max mA |
|---|---|---|---|
| VCC | 3.3 V, 5 VLogic supply; match the board. | ||
| GND | ground | ||
| SCL | I2C clock | ||
| SDA | I2C data | ||
| OE | digitalOutput enable, active LOW (pulled low). | ||
| V+ | 5 V, power inServo power (terminal block), 5-6 V from its own supply. | ||
| PWM0 | not connectedChannel 0: servo signal or LED. | ||
| PWM1 | not connectedChannel 1: servo signal or LED. | ||
| PWM2 | not connectedChannel 2: servo signal or LED. | ||
| PWM3 | not connectedChannel 3: servo signal or LED. | ||
| PWM4 | not connectedChannel 4: servo signal or LED. | ||
| PWM5 | not connectedChannel 5: servo signal or LED. | ||
| PWM6 | not connectedChannel 6: servo signal or LED. | ||
| PWM7 | not connectedChannel 7: servo signal or LED. | ||
| PWM8 | not connectedChannel 8: servo signal or LED. | ||
| PWM9 | not connectedChannel 9: servo signal or LED. | ||
| PWM10 | not connectedChannel 10: servo signal or LED. | ||
| PWM11 | not connectedChannel 11: servo signal or LED. | ||
| PWM12 | not connectedChannel 12: servo signal or LED. | ||
| PWM13 | not connectedChannel 13: servo signal or LED. | ||
| PWM14 | not connectedChannel 14: servo signal or LED. | ||
| PWM15 | not connectedChannel 15: servo signal or LED. |
Size and material
- Size
- 63 × 3 × 25 mm
- Weight
- 5.5 g
- Material
- pcb
- Sold by the
- piece
Works with
- Arduino Uno R3
- Arduino Nano
- Arduino Mega 2560 Rev3
- Arduino UNO R4 WiFi
- Arduino UNO R4 Minima
- Arduino Nano ESP32
- ESP32 DevKitC (ESP32-WROOM-32, 38-pin)
- ESP32-S3-DevKitC-1 (N8R8)
- Adafruit ESP32-S3 Feather (4 MB flash, 2 MB PSRAM)
- Seeed XIAO ESP32S3 Sense (camera + mic)
- Seeed XIAO ESP32C3
- Seeed XIAO ESP32C6
- Raspberry Pi Pico (RP2040)
- Raspberry Pi Pico W (RP2040, Wi-Fi)
- Raspberry Pi Pico 2 (RP2350)
- Raspberry Pi Pico 2 W (RP2350, Wi-Fi)
- Seeed XIAO RP2040
- Seeed XIAO nRF52840 (Bluetooth LE)
- Raspberry Pi 5 (4 GB)
- Raspberry Pi 4 Model B (4 GB)
- Raspberry Pi Zero 2 W
Projects using it
No public project uses it yet. Design one that does.