TMC2209 stepper motor driver (BIGTREETECH, StepStick)
A very quiet stepper driver, the kind used in modern 3D printers.
Trinamic TMC2209 on a StepStick-format carrier (BTT): STEP/DIR or single-wire UART, up to 1/256 microstepping, StealthChop2 near-silent drive, StallGuard4 sensorless homing. Motor supply VM 4.75-28 V, logic VIO 3-5 V. 2 A RMS, 2.8 A peak. Current set by the VREF trimmer (factory 1.2 V, about 0.9 A). Drop-in for A4988/DRV8825 sockets.
Electrical
- Supply voltage
- 3 to 28 V
- Talks over
- digital, uart
Needs alongside it
- VM needs a 4.75-28 V supply sized for the motor. Set VREF (current) before connecting the motor.
Pins
| Pin | Can do | Max V | Max mA |
|---|---|---|---|
| EN | digitalJ1-1. Enable: LOW (GND) = motor on. | ||
| MS1 | digitalJ1-2. Microstep select / UART address bit. | ||
| MS2 | digitalJ1-3. Microstep select / UART address bit. | ||
| PDN_UART | serial RX, serial TX, digitalJ1-4. Single-wire UART, connected at the factory (manual 8.1). | ||
| PDN_UART2 | not connectedJ1-5. Alternative UART pin, only live if the board resistor is moved (manual 8.1). | ||
| CLK | digitalJ1-6. Clock input; tie to GND for the internal clock. | ||
| STEP | digitalJ1-7. One pulse = one (micro)step. | ||
| DIR | digitalJ1-8. Direction. | ||
| VM | power inJ2-1. Motor supply 4.75-28 V. | ||
| GND | groundJ2-2. Motor ground. | ||
| A2 | not connectedJ2-3. Motor coil A. | ||
| A1 | not connectedJ2-4. Motor coil A. | ||
| B1 | not connectedJ2-5. Motor coil B. | ||
| B2 | not connectedJ2-6. Motor coil B. | ||
| VCC_IO | 3.3 V, 5 VJ2-7. Logic supply, 3-5 V: match the board. | ||
| GND2 | groundJ2-8. Logic ground. |
Works with
- Arduino Uno R3
- Arduino Nano
- Arduino Mega 2560 Rev3
- Arduino UNO R4 WiFi
- Arduino UNO R4 Minima
- Arduino Nano ESP32
- ESP32 DevKitC (ESP32-WROOM-32, 38-pin)
- ESP32-S3-DevKitC-1 (N8R8)
- Adafruit ESP32-S3 Feather (4 MB flash, 2 MB PSRAM)
- Seeed XIAO ESP32S3 Sense (camera + mic)
- Seeed XIAO ESP32C3
- Seeed XIAO ESP32C6
- Raspberry Pi Pico (RP2040)
- Raspberry Pi Pico W (RP2040, Wi-Fi)
- Raspberry Pi Pico 2 (RP2350)
- Raspberry Pi Pico 2 W (RP2350, Wi-Fi)
- Seeed XIAO RP2040
- Seeed XIAO nRF52840 (Bluetooth LE)
- Raspberry Pi 5 (4 GB)
- Raspberry Pi 4 Model B (4 GB)
- Raspberry Pi Zero 2 W
Projects using it
No public project uses it yet. Design one that does.